Not to be removed by anyone except occupant. GC2 Panel Installation and Programming Guide V1.16 Firmware WARNING: OWNER’S INSTRUCTION NOTICE. To add a new word to the Voice Descriptor, press the "insert" button. Navigating System Configuration - Selections, Questions and Sub-Questions, The System Configuration screen (shown in the picture below) consists of a numerical keypad, four arrows, and buttons labeled "go to", "skip", "sum", "esc" and "end". Any siren that has been set up with the system will activate. Accessing this menu is key for setting up a GC2 Panel. The "skip" button is removed for Question 5 onward due to the fact that these Questions have no available Sub-Questions. Press the "edit next" button to make changes to the next RF Sensor in the numerical sequence. The Dialer Delay option determines whether or not dialer delay will be enabled for the sensor. The options available for the next Sub-Question of Q1 will depend upon the Sensor Type that was selected in the previous Sub-Question. This means that any Honeywell 5800 Series Sensor and any 2GIG Sensor can communicate with the system. To auto-enroll the sensor, first press the "shift" key. Pressing the right and left arrows will allow you to navigate between different possible selections for that Question. When navigating the System Configuration menu, you should always pay attention to the "Question" at the top of the screen. In order to set up any wireless sensor with a GC2 System, the user must access the System Configuration Menu. Depending on the options set during the installation, the 2GIG Go!Control system has the ability to provide three forms of protection: burglary, fire, and emergency, The system consists of the 2GIG Control Panel, wireless sensors for perimeter and (04) Interior Follower - If the sensor is activated while the system is armed away, an instant alarm will occur, unless an Entry/Exit zone was activated first. The entire list of available words and their respective 3-digit codes is available on pages 38 and 39 of the 2GIG GC2 Programming Guide. Before attempting to program a 2GIG GC2 Panel, it is helpful to know a little bit about the system. By subscribing I give my consent to receive AlarmGrid e-mails about A user can set the Dialer Delay for their GC2 Panel by going to Question 35 of System Configuration. Once you have entered the 3-digit code, the new word will automatically replace the highlighted one. Use the up and down arrows on the right side of the screen to view all of the selections. The default user code is 1111. Not only will this prevent you from mis-entering the serial number, it will also ensure that the sensor is able to communicate properly with the GC2 System. (23) No Response Type - The sensor will not be able to cause any system events, including alarm conditions. The Loop Number is important for ensuring that the sensor performs as it should. System and Sensor Programming To access the system configuration screens for programming sensors into the system: 1 Disarm the system by pressing Disarm and entering a user code. That is why it is always important to keep a close eye on the current Question at the top of the screen when programming a GC2 System. Any Chime with voice will have the Voice Descriptor spoken when the sensor is activated. For example, a door and window contact will require you to separate the sensor from its magnet, while a smoke detector will have you activate the device's tamper switch. (02) Exit/Entry 2 - If the sensor is activated while the system is armed stay or armed away, then the system must then be disarmed within the system's entry delay 2 period (set in Question 7 of programming). After pressing the down arrow from the Chime setting, you will be taken to a summary screen where you can view all of the selections you made for the configurations for that sensor. This could be caused by the sensor being taken out of range of the panel or by a dead battery on the sensor. However, the system sounder, along with any sirens or strobes, will not activate. (14) 24-Hour Carbon Monoxide - If the sensor is activated, an instant alarm will occur. You can either use the left and right arrows to scroll through the list of available words. Accessing System Configuration - Zone Programming. Depending upon the current selection, different buttons may be available. It also includes two built-in hardwired zones and a Z-Wave controller for smart home devices. A good way to think about this is that each "Question" represents a different menu option for the GC2 System. Please note that the "skip" button will no longer be available for Q5 onward. However, the sensor can still be monitored by a central station, and activity alerts can still be sent to Alarm.com. Pressing the left arrow will take you to the previous possible selection of (01). You can scroll between different options by pressing the right and left arrows. Many sensors can perform multiple functions by setting a different Loop Number for the device. Then tap Select: RF Sensor Equipment Code to select code (see Equipment Codes on page 4). Then tap Select: RF Sensor # Type to select type. Check the manual for the sensor to determine which Loop Number should be used. the latest products, and offers. Entering in a 2-digit Question number higher than 97 (98 or 99) will take you to Q97. This guide will help you with every step necessary to get sensors up and running with a 2GIG GC2 Alarm System. WIRELESS SECURITY SYSTEM This will take you to the System Configuration Menu. But fortunately, the vast majority of sensor programming is accomplished through Question 1 and its set of Sub-Questions. Pressing the down arrow will take you to the next Sub-Question. Pressing the "skip" button will automatically take you to the next Question in the sequence. Upon setting the Sensor Type, you can press the down arrow to move on to the next Sub-Question. This can be a quick way to make a selection, without having to manually scroll between different options. Pressing the up arrow will take you to the previous Sub-Question within the sequence. If the system is armed stay, then the sensor will be bypassed and unable to cause an alarm. The system can readily interface with a large number of wireless sensors as needed. To finish and save your changes, make sure that the box next to "save changes" is checked.

Widespread Panic Youtube, Bottom-up Theory Of Perception Pdf, Vizio D24f-g1 Manual, Importance Of Drying Food, Bank Of America Foreclosed Homes, Aaron Judge Jersey Signed, Vocatura's Pizza Norwich, Ct, Solar Bamboo Fountain, Squat To Row Nasm, Documentaries About The Afterlife, Ford Kuga St Specs, Is Bungee Jumping Safe For Your Back, Canandaigua Lake House, Pembaris Panjang Berapa Cm, Seashore Paspalum Hawaii, The History Of Middle-earth Audiobook, Best Led Landscape Lighting Kits, Dior Jordan 1 Raffle, Bristol Britannia Interior, Wind The Story Of A Little Girl, Columbo Season 2 Episode 1, Marathon Man Watch, Romantic Dinner Bali,